Just How to Install a Bath Tub Yourself
Just How to Install a Bath Tub Yourself
Blog Article
Each person will have their unique thoughts involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a bathtub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a brand-new one is additionally a reasonably hard job. If the old tub is readily obtainable, the job can move speedily; if you need to open a wall to get rid of the old bathtub and place the brand-new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will require a helper to move out the old tub and embeded in the brand-new one. Ensure you have certified on your own for the task and fit trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is better to take into consideration using one before you begin. Opportunities are you may need a specialist plumber to make tube links.
This short article will certainly assist you install a brand-new tub in your restroom if you have actually currently purchased a brand-new bathtub and do not need to change the setup of your previous supply of water pipelines.
Your devices and product checklist must comprise the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing taps can be rather problematic as a result of the restricted gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any type of old sealing substance.
Prior to going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin guaranteeing that the washers are in place between the faucet and also the sink. Safeguard the faucet in position with the maker offered backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type ought to be connected to the tap finishes initially, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Bath tub
Utilizing both wooden boards under its feet, place the tub in the required placement. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level as well as changing the feet on the bathtub until the level checks out level.
To install faucets, fit all-time low of the furthest flexible tap adapter to the proper supply pipe by making a compression join; after that do the exact same for the other tap.
Activate the water system as well as check all joints and also brand-new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as also examine the overflow electrical outlet and the regular electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and also securing around the bathtub should wait up until the bath tub has been made use of a minimum of when as this will resolve it into its last position.
Planning for the Installation
To start with, the supporting structure supplied with the bath must be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to prevent stress on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bathroom and also the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water before securing, to permit the motion experienced when the tub is in usage. The sealer can split relatively early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly offered on the market. It is suggested to fit the ceramic tiles utilizing waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you liked our excerpt about Tools You Need to Install a New Bathtub . Thanks a ton for finding the time to read through our piece of content. Enjoyed our entry? Please share it. Let other people check it out. Bless you for your time. Don't forget to visit our site back soon.
Get An Estimate
Report this page